Ржавчина – Система уведомления об электричестве

This system will send notifications as binary numbers on RF Pagers – helpful when defending your base.

Setting this up can take around 30 minutes meaning it’s suitable for big bases and dealing with the threat of frequent attacks on your compound.

Описание

HBHF sensors around your base can be assigned a number. The setup in the blueprint will broadcast this number, meaning you can place quite a few sensors, preferably with some order. If a sensor is triggered RF pagers will send you a number indicating where someone is.

В этом случае, you can broadcast up to 64 different numbers while having to carry only 2 RF Pagers. One-pager has a number lower than the other one, например, 33 (represents 0), другой 44 (represents 1).

Преимущества:

• Sensors triggered by strangers will tell you where to look for the enemy
• this allows everyone to focus on fighting
• plus it can be enhanced but that information will be provided in another guide

Примечание:

The system will clear its temporal memory meaning:

• When you hear the first signal, pay attention to it and the next 3 followings.
• There might be the fifth signal, that’s just the system powering memory cells to clear them.
• This can be fixed but in order to preserve some energy, ресурсы, space and time just ignore the fifth/sixth signal.

Blueprint Overview

This system can be split into 4 части :

1. Broadcasting machine
2. ID storage
3. OR Switches
4. Sensors

The fifth section provides some information on how to connect the remaining stuff.

Some information on the wires:

• green wires will provide power 24/7
• blue wires provide powers as long as the device they’re coming from is powered
• yellow wires provide power when a condition of the device the power would come from is true

Broadcasting Setup

Для 2 seconds one digit will be broadcasted, then the next one until all digits have been sent.

Aka set these timers to 2 секунды.

Here’s an overview of how the broadcasting setup looks – blindly copy the stuff since sometimes the order in which electrical branches lead power somewhere, имеет значение.

The Note 1 OR Switches receive power from another device, which will be addressed in the next sections, ignore their input for now.

The left RF Broadcaster sends numbers representing zeros, the other broadcaster numbers represent ones.

ID Storage

This is where the binary numbers are stored.

• Those timers are set to 8 секунды
• the outputs of the OR switches can’t be seen here yet, the next section will address that
• the wires leading “включить” inputs of the timers will be addressed in section 4

You can see groups of 4 memory cells so to speak, each of those groups represents a number. The one in the very right is digit 1, the one next to its number 2, и так далее.

В любом случае, the way they store numbers, well you can google binary numbers xD or take a look at the example

• 0000 = 0
• 0001 = 1
• 0010 = 2
• 0011 = 3
• 0100 = 4

Видеть, the next bigger number you can create with only 0’s and 1’s represents the decimal number and so on.

Here’s the blueprint for the ID storage:

Set the memory states of the memory cells manually by turning on their timer and leading power from a generator or something into their set input.

Then disconnect the set input again, and turn on the next cell you want to be 1 / positive using this method.

OR Switch Setup

This is basically just a big “дерево” combining signals from the memory cells.

The images show 12 OR switches per digit, meaning this system could deal with up to 13 коды (the lowest OR switches have 2 inputs available).

You’d need 63 OR switches per digit in order to combine the signals of 64 ИДЕНТИФИКАТОР.

Anyway here’s how it looks:

Sensors

This is quite easy:

• place an HBHF sensor, lead its power out to an AND switch
• the other input of the switch will constantly receive power so the signal works properly
• lead the output energy of the AND switch to a branch
• lead the power out of that branch to the timer (the ones mentioned in section 2) that will power the ID (тот 4 memory cells in your ID storage) you want to assign this sensor
• branch off power and run that into one of the OR switches in that orange box
• you can add more than just these 3 or switches if you want to be able to broadcast more than just 3 цифры, с 63 of these you can deal with 64 сигналы, like with the other OR Switches

Connecting the Systems

The OR Switches covered with “Note 1” receive power from the big array of OR Switches (Раздел 3).

Check this image to get an idea of how they’re wired:

The ID storage is connected to that mass of OR switches, here’s how they’re connected. In order to create more ID’s, just scale this.