تخطى الى المحتوى
أعمال الشغب

أعمال الشغب

  • بيت
  • أخبار
  • خطوط إرشاد
  • أدلة الفيديو
  • ملاحظات التصحيح
  • بلغ عن سوء معاملة
  • تبديل شكل البحث
تونغوشكا: الزيارة

تونغوشكا: الزيارة – Radio Tower Puzzle Solution Guide

نشر على 07/11/2021 بواسطة Rotorist لا تعليقات على تونغوشكا: الزيارة – Radio Tower Puzzle Solution Guide
  • عنوان: تونغوشكا: الزيارة
  • تاريخ الافراج عنه: يونيو 4, 2021
  • المطور: ورشة عمل الدوار
  • الناشر: ورشة عمل الدوار

This guide will show you how to solve the radio tower puzzle in Tunguska: الزيارة. Please note that this guide contains spoilers. We highly recommend reading this guide if you have tried and couldn’t solve the puzzle.

Radio Tower Puzzle Guide

The main task in Station 11 is to repair the radio repeater tower so that Roman can find out the general location of the missing hunting group. The radio tower control is located in Station 11 inside a small house near the entrance. It’s powered by a power generator outside the house, but it requires 3 units of gasoline.

After turning on the generator, there are three containers on the radio control: a fuse box, and two resistor boxes. So you will need to put a fuse in the fusebox and a resistor in each resistor box.

Next to the house, there’s a large warehouse with electrified orbs floating around. On the wall of the warehouse near the metal shipping container, there’s another fusebox, and you can find the fuse inside. There’s a dead body in the middle of the warehouse, and you can find a key to the locker room of the warehouse, as well as a note showing the formula for calculating the required resistors (R = V/I). In the locker room, you can find the resistors inside a filing cabinet, with different specs – 100 ohms, 200 ohms, 250 ohms, إلخ.

After you have the fuse and resistors, first read the description of the fusebox, which says it needs a fuse that can handle a max of 1.6A of current. The fuse you found in the warehouse says it can handle 1.6A of current, and 800V of voltage. Place the fuse in the fusebox of the radio tower control. For the resistors, since R = V/I, so 800V divided by 1.6A is 500 Ohm. You just need to put any resistors in the resistor boxes so that their ohm rating adds up to 500 ohms. The only way is doing this is to put a 200 ohms resistor in one box, و أ 300 ohm one in the other (order doesn’t matter). Then pull the radio control switch to power it on.

هذا كل ما نشاركه اليوم من أجل هذا تونغوشكا: الزيارة مرشد. تم إنشاء هذا الدليل وكتابته في الأصل بواسطة Rotorist. في حالة فشلنا في تحديث هذا الدليل, يمكنك العثور على آخر تحديث باتباع هذا وصلة.

إذا كنت تعتقد أن أيًا من محتويات هذا الموقع ينتهك حقوقك, بما في ذلك حقوق الملكية الفكرية الخاصة بك, يرجى الاتصال بنا على الفور باستخدام نموذج الاتصال الخاص بنا.
خطوط إرشاد العلامات:تونغوشكا: الزيارة

آخر الملاحة

المنشور السابق: Roblox Science Simulator Codes (يوليو 2021) – Free Luck Boost and More
المشاركة التالية: Left Alive – Wanzer Crusher Achievement Guide

ترك الرد إلغاء الرد

لن يتم نشر عنوان بريدك الإلكتروني. تم وضع علامة على الحقول المطلوبة *

  • عنوان: تونغوشكا: الزيارة
  • تاريخ الافراج عنه: يونيو 4, 2021
  • المطور: ورشة عمل الدوار
  • الناشر: ورشة عمل الدوار

تنصل

ويستمد كل محتوى استشهد من مصادرها الخاصة. إذا كنت تعتقد أننا استخدمنا المحتوى الخاص بك دون إذن, تأكد من الوصول إلينا وسنأخذ الأمر على محمل الجد.
  • معلومات عنا
  • اتصل بنا
  • سياسة الخصوصية
  • شروط الخدمة

حقوق النشر © 2025 أعمال الشغب.

مشغل بواسطة PressBook News وورد موضوع